]> WPIA git - cassiopeia.git/blobdiff - lib/openssl/engines/asm/e_padlock-x86.pl
upd: openssl to 1.1.0
[cassiopeia.git] / lib / openssl / engines / asm / e_padlock-x86.pl
diff --git a/lib/openssl/engines/asm/e_padlock-x86.pl b/lib/openssl/engines/asm/e_padlock-x86.pl
new file mode 100644 (file)
index 0000000..bf6b312
--- /dev/null
@@ -0,0 +1,618 @@
+#! /usr/bin/env perl
+# Copyright 2011-2016 The OpenSSL Project Authors. All Rights Reserved.
+#
+# Licensed under the OpenSSL license (the "License").  You may not use
+# this file except in compliance with the License.  You can obtain a copy
+# in the file LICENSE in the source distribution or at
+# https://www.openssl.org/source/license.html
+
+
+# ====================================================================
+# Written by Andy Polyakov <appro@openssl.org> for the OpenSSL
+# project. The module is, however, dual licensed under OpenSSL and
+# CRYPTOGAMS licenses depending on where you obtain it. For further
+# details see http://www.openssl.org/~appro/cryptogams/.
+# ====================================================================
+
+# September 2011
+#
+# Assembler helpers for Padlock engine. Compared to original engine
+# version relying on inline assembler and compiled with gcc 3.4.6 it
+# was measured to provide ~100% improvement on misaligned data in ECB
+# mode and ~75% in CBC mode. For aligned data improvement can be
+# observed for short inputs only, e.g. 45% for 64-byte messages in
+# ECB mode, 20% in CBC. Difference in performance for aligned vs.
+# misaligned data depends on misalignment and is either ~1.8x or 2.9x.
+# These are approximately same factors as for hardware support, so
+# there is little reason to rely on the latter. On the contrary, it
+# might actually hurt performance in mixture of aligned and misaligned
+# buffers, because a) if you choose to flip 'align' flag in control
+# word on per-buffer basis, then you'd have to reload key context,
+# which incurs penalty; b) if you choose to set 'align' flag
+# permanently, it limits performance even for aligned data to ~1/2.
+# All above mentioned results were collected on 1.5GHz C7. Nano on the
+# other hand handles unaligned data more gracefully. Depending on
+# algorithm and how unaligned data is, hardware can be up to 70% more
+# efficient than below software alignment procedures, nor does 'align'
+# flag have affect on aligned performance [if has any meaning at all].
+# Therefore suggestion is to unconditionally set 'align' flag on Nano
+# for optimal performance.
+
+$0 =~ m/(.*[\/\\])[^\/\\]+$/; $dir=$1;
+push(@INC,"${dir}","${dir}../../crypto/perlasm");
+require "x86asm.pl";
+
+$output=pop;
+open STDOUT,">$output";
+
+&asm_init($ARGV[0],$0);
+
+%PADLOCK_PREFETCH=(ecb=>128, cbc=>64); # prefetch errata
+$PADLOCK_CHUNK=512;    # Must be a power of 2 larger than 16
+
+$ctx="edx";
+$out="edi";
+$inp="esi";
+$len="ecx";
+$chunk="ebx";
+
+&function_begin_B("padlock_capability");
+       &push   ("ebx");
+       &pushf  ();
+       &pop    ("eax");
+       &mov    ("ecx","eax");
+       &xor    ("eax",1<<21);
+       &push   ("eax");
+       &popf   ();
+       &pushf  ();
+       &pop    ("eax");
+       &xor    ("ecx","eax");
+       &xor    ("eax","eax");
+       &bt     ("ecx",21);
+       &jnc    (&label("noluck"));
+       &cpuid  ();
+       &xor    ("eax","eax");
+       &cmp    ("ebx","0x".unpack("H*",'tneC'));
+       &jne    (&label("noluck"));
+       &cmp    ("edx","0x".unpack("H*",'Hrua'));
+       &jne    (&label("noluck"));
+       &cmp    ("ecx","0x".unpack("H*",'slua'));
+       &jne    (&label("noluck"));
+       &mov    ("eax",0xC0000000);
+       &cpuid  ();
+       &mov    ("edx","eax");
+       &xor    ("eax","eax");
+       &cmp    ("edx",0xC0000001);
+       &jb     (&label("noluck"));
+       &mov    ("eax",1);
+       &cpuid  ();
+       &or     ("eax",0x0f);
+       &xor    ("ebx","ebx");
+       &and    ("eax",0x0fff);
+       &cmp    ("eax",0x06ff);         # check for Nano
+       &sete   ("bl");
+       &mov    ("eax",0xC0000001);
+       &push   ("ebx");
+       &cpuid  ();
+       &pop    ("ebx");
+       &mov    ("eax","edx");
+       &shl    ("ebx",4);              # bit#4 denotes Nano
+       &and    ("eax",0xffffffef);
+       &or     ("eax","ebx")
+&set_label("noluck");
+       &pop    ("ebx");
+       &ret    ();
+&function_end_B("padlock_capability")
+
+&function_begin_B("padlock_key_bswap");
+       &mov    ("edx",&wparam(0));
+       &mov    ("ecx",&DWP(240,"edx"));
+&set_label("bswap_loop");
+       &mov    ("eax",&DWP(0,"edx"));
+       &bswap  ("eax");
+       &mov    (&DWP(0,"edx"),"eax");
+       &lea    ("edx",&DWP(4,"edx"));
+       &sub    ("ecx",1);
+       &jnz    (&label("bswap_loop"));
+       &ret    ();
+&function_end_B("padlock_key_bswap");
+
+# This is heuristic key context tracing. At first one
+# believes that one should use atomic swap instructions,
+# but it's not actually necessary. Point is that if
+# padlock_saved_context was changed by another thread
+# after we've read it and before we compare it with ctx,
+# our key *shall* be reloaded upon thread context switch
+# and we are therefore set in either case...
+&static_label("padlock_saved_context");
+
+&function_begin_B("padlock_verify_context");
+       &mov    ($ctx,&wparam(0));
+       &lea    ("eax",($::win32 or $::coff) ? &DWP(&label("padlock_saved_context")) :
+                      &DWP(&label("padlock_saved_context")."-".&label("verify_pic_point")));
+       &pushf  ();
+       &call   ("_padlock_verify_ctx");
+&set_label("verify_pic_point");
+       &lea    ("esp",&DWP(4,"esp"));
+       &ret    ();
+&function_end_B("padlock_verify_context");
+
+&function_begin_B("_padlock_verify_ctx");
+       &add    ("eax",&DWP(0,"esp")) if(!($::win32 or $::coff));# &padlock_saved_context
+       &bt     (&DWP(4,"esp"),30);             # eflags
+       &jnc    (&label("verified"));
+       &cmp    ($ctx,&DWP(0,"eax"));
+       &je     (&label("verified"));
+       &pushf  ();
+       &popf   ();
+&set_label("verified");
+       &mov    (&DWP(0,"eax"),$ctx);
+       &ret    ();
+&function_end_B("_padlock_verify_ctx");
+
+&function_begin_B("padlock_reload_key");
+       &pushf  ();
+       &popf   ();
+       &ret    ();
+&function_end_B("padlock_reload_key");
+
+&function_begin_B("padlock_aes_block");
+       &push   ("edi");
+       &push   ("esi");
+       &push   ("ebx");
+       &mov    ($out,&wparam(0));              # must be 16-byte aligned
+       &mov    ($inp,&wparam(1));              # must be 16-byte aligned
+       &mov    ($ctx,&wparam(2));
+       &mov    ($len,1);
+       &lea    ("ebx",&DWP(32,$ctx));          # key
+       &lea    ($ctx,&DWP(16,$ctx));           # control word
+       &data_byte(0xf3,0x0f,0xa7,0xc8);        # rep xcryptecb
+       &pop    ("ebx");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_aes_block");
+
+sub generate_mode {
+my ($mode,$opcode) = @_;
+# int padlock_$mode_encrypt(void *out, const void *inp,
+#              struct padlock_cipher_data *ctx, size_t len);
+&function_begin("padlock_${mode}_encrypt");
+       &mov    ($out,&wparam(0));
+       &mov    ($inp,&wparam(1));
+       &mov    ($ctx,&wparam(2));
+       &mov    ($len,&wparam(3));
+       &test   ($ctx,15);
+       &jnz    (&label("${mode}_abort"));
+       &test   ($len,15);
+       &jnz    (&label("${mode}_abort"));
+       &lea    ("eax",($::win32 or $::coff) ? &DWP(&label("padlock_saved_context")) :
+                      &DWP(&label("padlock_saved_context")."-".&label("${mode}_pic_point")));
+       &pushf  ();
+       &cld    ();
+       &call   ("_padlock_verify_ctx");
+&set_label("${mode}_pic_point");
+       &lea    ($ctx,&DWP(16,$ctx));   # control word
+       &xor    ("eax","eax");
+                                       if ($mode eq "ctr32") {
+       &movq   ("mm0",&QWP(-16,$ctx)); # load [upper part of] counter
+                                       } else {
+       &xor    ("ebx","ebx");
+       &test   (&DWP(0,$ctx),1<<5);    # align bit in control word
+       &jnz    (&label("${mode}_aligned"));
+       &test   ($out,0x0f);
+       &setz   ("al");                 # !out_misaligned
+       &test   ($inp,0x0f);
+       &setz   ("bl");                 # !inp_misaligned
+       &test   ("eax","ebx");
+       &jnz    (&label("${mode}_aligned"));
+       &neg    ("eax");
+                                       }
+       &mov    ($chunk,$PADLOCK_CHUNK);
+       &not    ("eax");                # out_misaligned?-1:0
+       &lea    ("ebp",&DWP(-24,"esp"));
+       &cmp    ($len,$chunk);
+       &cmovc  ($chunk,$len);          # chunk=len>PADLOCK_CHUNK?PADLOCK_CHUNK:len
+       &and    ("eax",$chunk);         # out_misaligned?chunk:0
+       &mov    ($chunk,$len);
+       &neg    ("eax");
+       &and    ($chunk,$PADLOCK_CHUNK-1);      # chunk=len%PADLOCK_CHUNK
+       &lea    ("esp",&DWP(0,"eax","ebp"));    # alloca
+       &mov    ("eax",$PADLOCK_CHUNK);
+       &cmovz  ($chunk,"eax");                 # chunk=chunk?:PADLOCK_CHUNK
+       &mov    ("eax","ebp");
+       &and    ("ebp",-16);
+       &and    ("esp",-16);
+       &mov    (&DWP(16,"ebp"),"eax");
+    if ($PADLOCK_PREFETCH{$mode}) {
+       &cmp    ($len,$chunk);
+       &ja     (&label("${mode}_loop"));
+       &mov    ("eax",$inp);           # check if prefetch crosses page
+       &cmp    ("ebp","esp");
+       &cmove  ("eax",$out);
+       &add    ("eax",$len);
+       &neg    ("eax");
+       &and    ("eax",0xfff);          # distance to page boundary
+       &cmp    ("eax",$PADLOCK_PREFETCH{$mode});
+       &mov    ("eax",-$PADLOCK_PREFETCH{$mode});
+       &cmovae ("eax",$chunk);         # mask=distance<prefetch?-prefetch:-1
+       &and    ($chunk,"eax");
+       &jz     (&label("${mode}_unaligned_tail"));
+    }
+       &jmp    (&label("${mode}_loop"));
+
+&set_label("${mode}_loop",16);
+       &mov    (&DWP(0,"ebp"),$out);           # save parameters
+       &mov    (&DWP(4,"ebp"),$inp);
+       &mov    (&DWP(8,"ebp"),$len);
+       &mov    ($len,$chunk);
+       &mov    (&DWP(12,"ebp"),$chunk);        # chunk
+                                               if ($mode eq "ctr32") {
+       &mov    ("ecx",&DWP(-4,$ctx));
+       &xor    ($out,$out);
+       &mov    ("eax",&DWP(-8,$ctx));          # borrow $len
+&set_label("${mode}_prepare");
+       &mov    (&DWP(12,"esp",$out),"ecx");
+       &bswap  ("ecx");
+       &movq   (&QWP(0,"esp",$out),"mm0");
+       &inc    ("ecx");
+       &mov    (&DWP(8,"esp",$out),"eax");
+       &bswap  ("ecx");
+       &lea    ($out,&DWP(16,$out));
+       &cmp    ($out,$chunk);
+       &jb     (&label("${mode}_prepare"));
+
+       &mov    (&DWP(-4,$ctx),"ecx");
+       &lea    ($inp,&DWP(0,"esp"));
+       &lea    ($out,&DWP(0,"esp"));
+       &mov    ($len,$chunk);
+                                               } else {
+       &test   ($out,0x0f);                    # out_misaligned
+       &cmovnz ($out,"esp");
+       &test   ($inp,0x0f);                    # inp_misaligned
+       &jz     (&label("${mode}_inp_aligned"));
+       &shr    ($len,2);
+       &data_byte(0xf3,0xa5);                  # rep movsl
+       &sub    ($out,$chunk);
+       &mov    ($len,$chunk);
+       &mov    ($inp,$out);
+&set_label("${mode}_inp_aligned");
+                                               }
+       &lea    ("eax",&DWP(-16,$ctx));         # ivp
+       &lea    ("ebx",&DWP(16,$ctx));          # key
+       &shr    ($len,4);                       # len/=AES_BLOCK_SIZE
+       &data_byte(0xf3,0x0f,0xa7,$opcode);     # rep xcrypt*
+                                               if ($mode !~ /ecb|ctr/) {
+       &movaps ("xmm0",&QWP(0,"eax"));
+       &movaps (&QWP(-16,$ctx),"xmm0");        # copy [or refresh] iv
+                                               }
+       &mov    ($out,&DWP(0,"ebp"));           # restore parameters
+       &mov    ($chunk,&DWP(12,"ebp"));
+                                               if ($mode eq "ctr32") {
+       &mov    ($inp,&DWP(4,"ebp"));
+       &xor    ($len,$len);
+&set_label("${mode}_xor");
+       &movups ("xmm1",&QWP(0,$inp,$len));
+       &lea    ($len,&DWP(16,$len));
+       &pxor   ("xmm1",&QWP(-16,"esp",$len));
+       &movups (&QWP(-16,$out,$len),"xmm1");
+       &cmp    ($len,$chunk);
+       &jb     (&label("${mode}_xor"));
+                                               } else {
+       &test   ($out,0x0f);
+       &jz     (&label("${mode}_out_aligned"));
+       &mov    ($len,$chunk);
+       &lea    ($inp,&DWP(0,"esp"));
+       &shr    ($len,2);
+       &data_byte(0xf3,0xa5);                  # rep movsl
+       &sub    ($out,$chunk);
+&set_label("${mode}_out_aligned");
+       &mov    ($inp,&DWP(4,"ebp"));
+                                               }
+       &mov    ($len,&DWP(8,"ebp"));
+       &add    ($out,$chunk);
+       &add    ($inp,$chunk);
+       &sub    ($len,$chunk);
+       &mov    ($chunk,$PADLOCK_CHUNK);
+    if (!$PADLOCK_PREFETCH{$mode}) {
+       &jnz    (&label("${mode}_loop"));
+    } else {
+       &jz     (&label("${mode}_break"));
+       &cmp    ($len,$chunk);
+       &jae    (&label("${mode}_loop"));
+
+&set_label("${mode}_unaligned_tail");
+       &xor    ("eax","eax");
+       &cmp    ("esp","ebp");
+       &cmove  ("eax",$len);
+       &sub    ("esp","eax");                  # alloca
+       &mov    ("eax", $out);                  # save parameters
+       &mov    ($chunk,$len);
+       &shr    ($len,2);
+       &lea    ($out,&DWP(0,"esp"));
+       &data_byte(0xf3,0xa5);                  # rep movsl
+       &mov    ($inp,"esp");
+       &mov    ($out,"eax");                   # restore parameters
+       &mov    ($len,$chunk);
+       &jmp    (&label("${mode}_loop"));
+
+&set_label("${mode}_break",16);
+    }
+                                               if ($mode ne "ctr32") {
+       &cmp    ("esp","ebp");
+       &je     (&label("${mode}_done"));
+                                               }
+       &pxor   ("xmm0","xmm0");
+       &lea    ("eax",&DWP(0,"esp"));
+&set_label("${mode}_bzero");
+       &movaps (&QWP(0,"eax"),"xmm0");
+       &lea    ("eax",&DWP(16,"eax"));
+       &cmp    ("ebp","eax");
+       &ja     (&label("${mode}_bzero"));
+
+&set_label("${mode}_done");
+       &mov    ("ebp",&DWP(16,"ebp"));
+       &lea    ("esp",&DWP(24,"ebp"));
+                                               if ($mode ne "ctr32") {
+       &jmp    (&label("${mode}_exit"));
+
+&set_label("${mode}_aligned",16);
+    if ($PADLOCK_PREFETCH{$mode}) {
+       &lea    ("ebp",&DWP(0,$inp,$len));
+       &neg    ("ebp");
+       &and    ("ebp",0xfff);                  # distance to page boundary
+       &xor    ("eax","eax");
+       &cmp    ("ebp",$PADLOCK_PREFETCH{$mode});
+       &mov    ("ebp",$PADLOCK_PREFETCH{$mode}-1);
+       &cmovae ("ebp","eax");
+       &and    ("ebp",$len);                   # remainder
+       &sub    ($len,"ebp");
+       &jz     (&label("${mode}_aligned_tail"));
+    }
+       &lea    ("eax",&DWP(-16,$ctx));         # ivp
+       &lea    ("ebx",&DWP(16,$ctx));          # key
+       &shr    ($len,4);                       # len/=AES_BLOCK_SIZE
+       &data_byte(0xf3,0x0f,0xa7,$opcode);     # rep xcrypt*
+                                               if ($mode ne "ecb") {
+       &movaps ("xmm0",&QWP(0,"eax"));
+       &movaps (&QWP(-16,$ctx),"xmm0");        # copy [or refresh] iv
+                                               }
+    if ($PADLOCK_PREFETCH{$mode}) {
+       &test   ("ebp","ebp");
+       &jz     (&label("${mode}_exit"));
+
+&set_label("${mode}_aligned_tail");
+       &mov    ($len,"ebp");
+       &lea    ("ebp",&DWP(-24,"esp"));
+       &mov    ("esp","ebp");
+       &mov    ("eax","ebp");
+       &sub    ("esp",$len);
+       &and    ("ebp",-16);
+       &and    ("esp",-16);
+       &mov    (&DWP(16,"ebp"),"eax");
+       &mov    ("eax", $out);                  # save parameters
+       &mov    ($chunk,$len);
+       &shr    ($len,2);
+       &lea    ($out,&DWP(0,"esp"));
+       &data_byte(0xf3,0xa5);                  # rep movsl
+       &mov    ($inp,"esp");
+       &mov    ($out,"eax");                   # restore parameters
+       &mov    ($len,$chunk);
+       &jmp    (&label("${mode}_loop"));
+    }
+&set_label("${mode}_exit");                    }
+       &mov    ("eax",1);
+       &lea    ("esp",&DWP(4,"esp"));          # popf
+       &emms   ()                              if ($mode eq "ctr32");
+&set_label("${mode}_abort");
+&function_end("padlock_${mode}_encrypt");
+}
+
+&generate_mode("ecb",0xc8);
+&generate_mode("cbc",0xd0);
+&generate_mode("cfb",0xe0);
+&generate_mode("ofb",0xe8);
+&generate_mode("ctr32",0xc8);  # yes, it implements own CTR with ECB opcode,
+                               # because hardware CTR was introduced later
+                               # and even has errata on certain C7 stepping.
+                               # own implementation *always* works, though
+                               # ~15% slower than dedicated hardware...
+
+&function_begin_B("padlock_xstore");
+       &push   ("edi");
+       &mov    ("edi",&wparam(0));
+       &mov    ("edx",&wparam(1));
+       &data_byte(0x0f,0xa7,0xc0);             # xstore
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_xstore");
+
+&function_begin_B("_win32_segv_handler");
+       &mov    ("eax",1);                      # ExceptionContinueSearch
+       &mov    ("edx",&wparam(0));             # *ExceptionRecord
+       &mov    ("ecx",&wparam(2));             # *ContextRecord
+       &cmp    (&DWP(0,"edx"),0xC0000005)      # ExceptionRecord->ExceptionCode == STATUS_ACCESS_VIOLATION
+       &jne    (&label("ret"));
+       &add    (&DWP(184,"ecx"),4);            # skip over rep sha*
+       &mov    ("eax",0);                      # ExceptionContinueExecution
+&set_label("ret");
+       &ret    ();
+&function_end_B("_win32_segv_handler");
+&safeseh("_win32_segv_handler")                        if ($::win32);
+
+&function_begin_B("padlock_sha1_oneshot");
+       &push   ("edi");
+       &push   ("esi");
+       &xor    ("eax","eax");
+       &mov    ("edi",&wparam(0));
+       &mov    ("esi",&wparam(1));
+       &mov    ("ecx",&wparam(2));
+    if ($::win32 or $::coff) {
+       &push   (&::islabel("_win32_segv_handler"));
+       &data_byte(0x64,0xff,0x30);             # push  %fs:(%eax)
+       &data_byte(0x64,0x89,0x20);             # mov   %esp,%fs:(%eax)
+    }
+       &mov    ("edx","esp");                  # put aside %esp
+       &add    ("esp",-128);                   # 32 is enough but spec says 128
+       &movups ("xmm0",&QWP(0,"edi"));         # copy-in context
+       &and    ("esp",-16);
+       &mov    ("eax",&DWP(16,"edi"));
+       &movaps (&QWP(0,"esp"),"xmm0");
+       &mov    ("edi","esp");
+       &mov    (&DWP(16,"esp"),"eax");
+       &xor    ("eax","eax");
+       &data_byte(0xf3,0x0f,0xa6,0xc8);        # rep xsha1
+       &movaps ("xmm0",&QWP(0,"esp"));
+       &mov    ("eax",&DWP(16,"esp"));
+       &mov    ("esp","edx");                  # restore %esp
+    if ($::win32 or $::coff) {
+       &data_byte(0x64,0x8f,0x05,0,0,0,0);     # pop   %fs:0
+       &lea    ("esp",&DWP(4,"esp"));
+    }
+       &mov    ("edi",&wparam(0));
+       &movups (&QWP(0,"edi"),"xmm0");         # copy-out context
+       &mov    (&DWP(16,"edi"),"eax");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_sha1_oneshot");
+
+&function_begin_B("padlock_sha1_blocks");
+       &push   ("edi");
+       &push   ("esi");
+       &mov    ("edi",&wparam(0));
+       &mov    ("esi",&wparam(1));
+       &mov    ("edx","esp");                  # put aside %esp
+       &mov    ("ecx",&wparam(2));
+       &add    ("esp",-128);
+       &movups ("xmm0",&QWP(0,"edi"));         # copy-in context
+       &and    ("esp",-16);
+       &mov    ("eax",&DWP(16,"edi"));
+       &movaps (&QWP(0,"esp"),"xmm0");
+       &mov    ("edi","esp");
+       &mov    (&DWP(16,"esp"),"eax");
+       &mov    ("eax",-1);
+       &data_byte(0xf3,0x0f,0xa6,0xc8);        # rep xsha1
+       &movaps ("xmm0",&QWP(0,"esp"));
+       &mov    ("eax",&DWP(16,"esp"));
+       &mov    ("esp","edx");                  # restore %esp
+       &mov    ("edi",&wparam(0));
+       &movups (&QWP(0,"edi"),"xmm0");         # copy-out context
+       &mov    (&DWP(16,"edi"),"eax");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_sha1_blocks");
+
+&function_begin_B("padlock_sha256_oneshot");
+       &push   ("edi");
+       &push   ("esi");
+       &xor    ("eax","eax");
+       &mov    ("edi",&wparam(0));
+       &mov    ("esi",&wparam(1));
+       &mov    ("ecx",&wparam(2));
+    if ($::win32 or $::coff) {
+       &push   (&::islabel("_win32_segv_handler"));
+       &data_byte(0x64,0xff,0x30);             # push  %fs:(%eax)
+       &data_byte(0x64,0x89,0x20);             # mov   %esp,%fs:(%eax)
+    }
+       &mov    ("edx","esp");                  # put aside %esp
+       &add    ("esp",-128);
+       &movups ("xmm0",&QWP(0,"edi"));         # copy-in context
+       &and    ("esp",-16);
+       &movups ("xmm1",&QWP(16,"edi"));
+       &movaps (&QWP(0,"esp"),"xmm0");
+       &mov    ("edi","esp");
+       &movaps (&QWP(16,"esp"),"xmm1");
+       &xor    ("eax","eax");
+       &data_byte(0xf3,0x0f,0xa6,0xd0);        # rep xsha256
+       &movaps ("xmm0",&QWP(0,"esp"));
+       &movaps ("xmm1",&QWP(16,"esp"));
+       &mov    ("esp","edx");                  # restore %esp
+    if ($::win32 or $::coff) {
+       &data_byte(0x64,0x8f,0x05,0,0,0,0);     # pop   %fs:0
+       &lea    ("esp",&DWP(4,"esp"));
+    }
+       &mov    ("edi",&wparam(0));
+       &movups (&QWP(0,"edi"),"xmm0");         # copy-out context
+       &movups (&QWP(16,"edi"),"xmm1");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_sha256_oneshot");
+
+&function_begin_B("padlock_sha256_blocks");
+       &push   ("edi");
+       &push   ("esi");
+       &mov    ("edi",&wparam(0));
+       &mov    ("esi",&wparam(1));
+       &mov    ("ecx",&wparam(2));
+       &mov    ("edx","esp");                  # put aside %esp
+       &add    ("esp",-128);
+       &movups ("xmm0",&QWP(0,"edi"));         # copy-in context
+       &and    ("esp",-16);
+       &movups ("xmm1",&QWP(16,"edi"));
+       &movaps (&QWP(0,"esp"),"xmm0");
+       &mov    ("edi","esp");
+       &movaps (&QWP(16,"esp"),"xmm1");
+       &mov    ("eax",-1);
+       &data_byte(0xf3,0x0f,0xa6,0xd0);        # rep xsha256
+       &movaps ("xmm0",&QWP(0,"esp"));
+       &movaps ("xmm1",&QWP(16,"esp"));
+       &mov    ("esp","edx");                  # restore %esp
+       &mov    ("edi",&wparam(0));
+       &movups (&QWP(0,"edi"),"xmm0");         # copy-out context
+       &movups (&QWP(16,"edi"),"xmm1");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_sha256_blocks");
+
+&function_begin_B("padlock_sha512_blocks");
+       &push   ("edi");
+       &push   ("esi");
+       &mov    ("edi",&wparam(0));
+       &mov    ("esi",&wparam(1));
+       &mov    ("ecx",&wparam(2));
+       &mov    ("edx","esp");                  # put aside %esp
+       &add    ("esp",-128);
+       &movups ("xmm0",&QWP(0,"edi"));         # copy-in context
+       &and    ("esp",-16);
+       &movups ("xmm1",&QWP(16,"edi"));
+       &movups ("xmm2",&QWP(32,"edi"));
+       &movups ("xmm3",&QWP(48,"edi"));
+       &movaps (&QWP(0,"esp"),"xmm0");
+       &mov    ("edi","esp");
+       &movaps (&QWP(16,"esp"),"xmm1");
+       &movaps (&QWP(32,"esp"),"xmm2");
+       &movaps (&QWP(48,"esp"),"xmm3");
+       &data_byte(0xf3,0x0f,0xa6,0xe0);        # rep xsha512
+       &movaps ("xmm0",&QWP(0,"esp"));
+       &movaps ("xmm1",&QWP(16,"esp"));
+       &movaps ("xmm2",&QWP(32,"esp"));
+       &movaps ("xmm3",&QWP(48,"esp"));
+       &mov    ("esp","edx");                  # restore %esp
+       &mov    ("edi",&wparam(0));
+       &movups (&QWP(0,"edi"),"xmm0");         # copy-out context
+       &movups (&QWP(16,"edi"),"xmm1");
+       &movups (&QWP(32,"edi"),"xmm2");
+       &movups (&QWP(48,"edi"),"xmm3");
+       &pop    ("esi");
+       &pop    ("edi");
+       &ret    ();
+&function_end_B("padlock_sha512_blocks");
+
+&asciz ("VIA Padlock x86 module, CRYPTOGAMS by <appro\@openssl.org>");
+&align (16);
+
+&dataseg();
+# Essentially this variable belongs in thread local storage.
+# Having this variable global on the other hand can only cause
+# few bogus key reloads [if any at all on signle-CPU system],
+# so we accept the penalty...
+&set_label("padlock_saved_context",4);
+&data_word(0);
+
+&asm_finish();
+
+close STDOUT;